ZZ-R Coilovers by Blitz - 350Z
A single mono tube design is adopted for the complete range. A large 44mm diameter low friction piston control initial damping, allowing a comfortable ride but a shart driving response.
DRIVABILITY AND COMFORT:
A 32 way damping rate is incorporated into both shock absorbers. With such a wide range of adjustable, driving performance and ride comfort are maintained at the highest level, even at low speed. Spring rate is setup for each vehicle. A comfortable ride can be achieved with the height adjustment function which allows enough stroke for any driving conditions.
The spring sheet and upper mounts are finished in a red alumite. The brackets are finished in a classy matt black. The height adjustment function is shown in millimeters, allowing a wide range of setting to suit any driving conditions.
Preload adjustment of the spring and the height can be adjusted separately. A variety of damping rates can be achieved through simple adjustment. Camber adjustment allows alignment to be set to personal preference.
The cylinder case is finished in a black chrome overlay and the bracket is finished in a special point to improve durability and anti-corrosion.
This damper can be overhauled to maintain prime condition.
Blitz Damper ZZR Coilover Kit (Adjustable), for Infiniti G35 Coupe
Note: -65mm to +70mm (Front) & -35mm to +10mm (Rear)
- A single mono tube shock absorber is adopted for all lineup
- 32 way adjustable damper rates
- Ideal for both street or circuit use.
- A large 44mm diameter piston is used (Some vehicles area excluded)
- This damper can be overhauled to maintain prime condition.
- 2003-2008 Nissan 350Z
Fiberglass Installation & Painting (FRP): There will always be minor sanding, shaving, cutting, tweaking, adjusting and/or filling will be required prior to installing these parts. All primer finish included with the parts but be sanded as well as other preparation work required before painting. All fitting and paint preparation is the responsibility of your body shop. Body kits must be test fitted on the vehicle prior to painting to check for any manufacturer's defect. The product's respective manufacturer nor Outcast Garage will be responsible for the quality of a body shop's work if it does not meet the customer's expectations.
Carbon Fiber Care (CF, CFRP): All carbon fiber products will require an automotive-grade clear coat for protection against the sun's UV rays unless the clear coat is included with the product from its respective manufacturer. Products infused with a 'UV Protection Resin Gel' should still be covered with an automotive-grade clear coat. Body kits must be test fitted on the vehicle prior to painting to check for any manufacturer's defect. The product's respective manufacturer nor Outcast Garage will be not not warranty or be responsible for discoloration of the carbon fiber nor be responsible for the quality of the clear coat applied by the body shop if it does not meet the customer's expectations.
Hand-Land Carbon Fiber (CF, CFRP): The 'Carbon Fiber Care' disclaimer also applies to hand-land carbon fiber products. Depending on the complexity and design of the product, there may be a slight and minor shift in the carbon fiber weaves. It is almost impossible to achieve 'perfection' with hand-land carbon fiber. These 'slight and minor shifts' in the carbon fiber weaves does not equate to the product being defective. If the weaves are extreme, and do not fall within an acceptable tolerance, then it will be eligible for a warranty replacement if the product has not been altered in anyway. A warranty claim must be filed first before any further action can be taken. Body kits must be test fitted on the vehicle prior to painting to check for any manufacturer's defect. Outcast Garage will not be responsible for a refused shipment of a carbon fiber product if it does not meet expectations without first initiating a warranty claim and receiving approval. Inspections and refusing of shipments are only for damaged products during transit (cracks, chips, bends, holes, scratches, etc).
Polyurethane Care, Installation & Painting (Poly): All polyurethane parts will come raw and unpainted. These parts are flexible so they may slightly warp during shipment. Slightly warped polyurethane parts are not considered defective. They will require a few hours of sunlight to return to its original shape from when it came out of the mold. Polyurethane parts are much different than factory OEM parts and require specific preparation before painting. Improper paint preparation will result in the paint not adhering to the bumper, pin holes and bubbles. It is normal for polyurethane parts to come slightly scratched with imperfections. Proper sanding during paint preparation will remove all imperfections. Please seek a professional and reputable body shop with experience with polyurethane aftermarket parts. Body kits must be test fitted on the vehicle prior to painting to check for any manufacturer's defect. The product's respective manufacturer nor Outcast Garage will not be responsible for the body shop's preparation, fitting and paint job if it does not meet the customer's expectations.
International Shipment Policy
- International orders are not eligble for refunds, cancellations or exchanges.
For customers outside of the United States and Canada, please fill out the following form for an accurate shipping quote. Canadian customers may proceed with check out to view shipping rates.
- Current international quote turnaround times are delayed due to new service acquisition to provide the best rates for our customers.