E-Level Air Management Package W/ Rocker Switch by Accuair
The e-Level™ Rocker Switch Air Management Package combines all of the highest quality components available to control your Air Springs in one easy to order part number. This kit includes our e-Level™ Controller with Rocker Switch interface, VU4 4-Corner Valve Manifold, 5-gallon ENDO Aluminum Air Tank, Serviceable Aluminum Air Filter, 3/8" D.O.T. Approved Plumbing Kit, and the most detailed Installation & Operation Manuals on the market. These packages are available with Single or Dual compressors and a variety of options shown above.
- Three Programable Heights
- Ride Height on Start
- Straight to Height
- Ridemonitor Mode
- Anti-Cross Loading
- Manages Air Compressors
- Trueposition Height Sensors
- Automatic Calibration
- Plug & Play
- Number of Savable Heights / 3 & All-Down
- Voltage Requirements / 9.5-16 Volts
- Current Requirements / Stage 1 - 44 AMPS (Max) / Stage 2 - 70 AMPS (Max)
- Compressor Recovery Time (100-150 PSI) / Stage 1 - 1 min 54 sec / Stage 2 - 52 sec
- Average Adjustment Time / 2.2 Seconds (from 10% to 50% of travel)
- Position Accuracy 1/8" at Wheel while parked or driving
- Leveling Response Time / 5 seconds parked - 45 Seconds Driving
- Auxiliary Device Compatibility / TouchPad™ Interface - Rocker Switch Interface - Wireless Key-Fob Module - (4) Universal "GND-Trigger" Inputs for use with customer supplied alarm, or other device. Triggers 3 Heights & All-Down
- Compatibility available upon request / Horizon Leveling Module - CANbus protocol for use with customer specific interfaces
Fiberglass Installation & Painting (FRP): There will always be minor sanding, shaving, cutting, tweaking, adjusting and/or filling will be required prior to installing these parts. All primer finish included with the parts but be sanded as well as other preparation work required before painting. All fitting and paint preparation is the responsibility of your body shop. Body kits must be test fitted on the vehicle prior to painting to check for any manufacturer's defect. The product's respective manufacturer nor Outcast Garage will be responsible for the quality of a body shop's work if it does not meet the customer's expectations.
Carbon Fiber Care (CF, CFRP): All carbon fiber products will require an automotive-grade clear coat for protection against the sun's UV rays unless the clear coat is included with the product from its respective manufacturer. Products infused with a 'UV Protection Resin Gel' should still be covered with an automotive-grade clear coat. Body kits must be test fitted on the vehicle prior to painting to check for any manufacturer's defect. The product's respective manufacturer nor Outcast Garage will be not not warranty or be responsible for discoloration of the carbon fiber nor be responsible for the quality of the clear coat applied by the body shop if it does not meet the customer's expectations.
Hand-Land Carbon Fiber (CF, CFRP): The 'Carbon Fiber Care' disclaimer also applies to hand-land carbon fiber products. Depending on the complexity and design of the product, there may be a slight and minor shift in the carbon fiber weaves. It is almost impossible to achieve 'perfection' with hand-land carbon fiber. These 'slight and minor shifts' in the carbon fiber weaves does not equate to the product being defective. If the weaves are extreme, and do not fall within an acceptable tolerance, then it will be eligible for a warranty replacement if the product has not been altered in anyway. A warranty claim must be filed first before any further action can be taken. Body kits must be test fitted on the vehicle prior to painting to check for any manufacturer's defect. Outcast Garage will not be responsible for a refused shipment of a carbon fiber product if it does not meet expectations without first initiating a warranty claim and receiving approval. Inspections and refusing of shipments are only for damaged products during transit (cracks, chips, bends, holes, scratches, etc).
Polyurethane Care, Installation & Painting (Poly): All polyurethane parts will come raw and unpainted. These parts are flexible so they may slightly warp during shipment. Slightly warped polyurethane parts are not considered defective. They will require a few hours of sunlight to return to its original shape from when it came out of the mold. Polyurethane parts are much different than factory OEM parts and require specific preparation before painting. Improper paint preparation will result in the paint not adhering to the bumper, pin holes and bubbles. It is normal for polyurethane parts to come slightly scratched with imperfections. Proper sanding during paint preparation will remove all imperfections. Please seek a professional and reputable body shop with experience with polyurethane aftermarket parts. Body kits must be test fitted on the vehicle prior to painting to check for any manufacturer's defect. The product's respective manufacturer nor Outcast Garage will not be responsible for the body shop's preparation, fitting and paint job if it does not meet the customer's expectations.
International Shipment Policy
- International orders are not eligble for refunds, cancellations or exchanges.
For customers outside of the United States and Canada, please fill out the following form for an accurate shipping quote. Canadian customers may proceed with check out to view shipping rates.
- Current international quote turnaround times are delayed due to new service acquisition to provide the best rates for our customers.