Accuair VU4 4-Corner Solenoid Valve Unit w/ 1/4" NPT Port

Manufacturer: Accuair

Part Number: AA-VU4-NPT

There are 2 in stock. (Please verify with us if inventory is lower than 2. Inventory does not apply to 'In-Store Pickups') Please review product information before ordering.


  • Sale
  • Regular price $ 515.00



VU4 4-CORNER SOLENOID VALVE UNIT W/ 1/4" NPT PORTS by Accuair

The VU4 4-Corner Valve Unit is engineered to provide the cleanest installation and most reliable operation on the market. This electronic solenoid valve unit inflates and deflates up to (4) individual Air Springs and has 1/4" NPT ports for all of its plumbing connections. Additional fittings will be required to use this valve manifold. The robust internal solenoid valve architecture maximizes flow rates, provides bubble-tight sealing, and guarantees operation up to 200 psi for millions of cycles. All of this technology is housed in a unique enclosure design which routes each of the solenoid wires to a single weatherproof connector, eliminating typically loose wires. This not only improves the appearance, but it also guarantees proper operation for every installation. With an overall size of only 5.28"x 2.75"x 2.75" and the ability to survive harsh under vehicle environments.

Features

  • Pre-Installed D.O.T. / PTC Fittings Inlet & Exhaust Ports on each end
  • All-Stainless Steel Valve Components 200 PSI Direct Operated Bubble-Tight Valves
  • 1/4" NPT Pressure Ports
  • Pre-Wired with Plug & Play Connector

Specs

  • Voltage Requirements / 10.5-16 Volts
  • Current Requirements / 1.1 AMPS (For each of the (8) Valves)
  • Number of Inlet Ports / 2
  • Number of Exhaust Port / 2
  • Max Operating Pressure / 200 PSI
  • Average Adjustment Time / 2.2 Seconds (from 10% to 50% of Travel)

Fiberglass Installation & Painting (FRP): There will always be minor sanding, shaving, cutting, tweaking, adjusting and/or filling will be required prior to installing these parts. All primer finish included with the parts but be sanded as well as other preparation work required before painting. All fitting and paint preparation is the responsibility of your body shop. The product's respective manufacturer nor Outcast Garage will be responsible for the quality of a body shop's work if it does not meet the customer's expectations.

Carbon Fiber Care (CF, CFRP): All carbon fiber products will require an automotive-grade clear coat for protection against the sun's UV rays unless the clear coat is included with the product from its respective manufacturer. Products infused with a 'UV Protection Resin Gel' should still be covered with an automotive-grade clear coat. The product's respective manufacturer nor Outcast Garage will be not not warranty or be responsible for discoloration of the carbon fiber nor be responsible for the quality of the clear coat applied by the body shop if it does not meet the customer's expectations. 

Hand-Land Carbon Fiber (CF, CFRP): The 'Carbon Fiber Care' disclaimer also applies to hand-land carbon fiber products. Depending on the complexity and design of the product, there may be a slight and minor shift in the carbon fiber weaves. It is almost impossible to achieve 'perfection' with hand-land carbon fiber. These 'slight and minor shifts' in the carbon fiber weaves does not equate to the product being defective. If the weaves are extreme, and do not fall within an acceptable tolerance, then it will be eligible for a warranty replacement if the product has not been altered in anyway. A warranty claim must be filed first before any further action can be taken. Outcast Garage will not be responsible for a refused shipment of a carbon fiber product if it does not meet expectations without first initiating a warranty claim and receiving approval. Inspections and refusing of shipments are only for damaged products during transit (cracks, chips, bends, holes, scratches, etc).

Polyurethane Care, Installation & Painting (Poly): All polyurethane parts will come raw and unpainted. These parts are flexible so they may slightly warp during shipment. Slightly warped polyurethane parts are not considered defective. They will require a few hours of sunlight to return to its original shape from when it came out of the mold. Polyurethane parts are much different than factory OEM parts and require specific preparation before painting. Improper paint preparation will result in the paint not adhering to the bumper, pin holes and bubbles. It is normal for polyurethane parts to come slightly scratched with imperfections. Proper sanding during paint preparation will remove all imperfections. Please seek a professional and reputable body shop with experience with polyurethane aftermarket parts. The product's respective manufacturer nor Outcast Garage will not be responsible for the body shop's preparation, fitting and paint job if it does not meet the customer's expectations. 

HAVE A QUESTION?

Be the first to ask a question about this.

Ask a Question

International Shipment Policy

  • International orders are not eligble for refunds, cancellations or exchanges.
  • For customers outside of the United States and Canada, please fill out the following form for an accurate shipping quote. Canadian customers may proceed with check out to view shipping rates.

  • Current international quote turnaround times are delayed due to new service acquisition to provide the best rates for our customers.