GKTech 4130 High Tensile Steel Steering Rack Spacer Set - Nissan Skyline, 350Z, 240SX / Infiniti G35

by GKtech

$ 32.00
You'll earn OG Points with this product!

(Click to Pre-Qualify)

Please carefully review the vehicle application below before purchasing.

Price Match | Make an Offer


The GKTECH high tensile 4130 zinc coated tie rod extenders screw on to the end of either standard or aftermarket tie rods and allow the tie rods to travel further into the steering rack which creates more steering lock. Great for drift or getting out of parking spots. Can be used either with or without the extra washer (included) to offer a grand total of 0.74'' (19mm) extra lock without compromising on the amount of thread left in the steering rack. - DIY installation (not as easy as the washer install but still not too hard) - CNC machined high tensile zinc coated 4130 steel

Vehicle Compatibility: - Nissan 240sx - Nissan S13 Silvia - Nissan S14 240SX - Nissan S15 240SX - Nissan Skyline R32 GTS-T (2WD) - Nissan Skyline R33 GTS-T (2WD) - Nissan Skyline R34 GTT (2WD) - Nissan Cefiro A31 - Nissan Z32 300ZX - Nissan Z33 350Z - Nissan V35 Skyline


Do I need to buy 1 of these rack spacers or 2?

You only need to buy 1 as buying 2 offers no benefit to the improvement of the steering lock. The way that these work is that they take advantage of extra travel available within the steering rack (which does have a limit). Hence the 0.51'' (13mm) bolt on on the LH side of the rack and the 0.23'' (6mm) washer on the RH side of the rack. Adding an extra rack spacer won't give more lock. In the event that your tie rod ends are too short then in that case using another bolt on rack spacer (on the RH side) would be okay.

How does this steering rack spacer work?

The steering rack spacer screws between the steering rack and your LH side tie rod. It allows the steering rack to travel an extra 0.51'' (13mm) while the washer which is to be installed on the RH side allows for an additional 0.23'' (6mm) of travel. Giving a grand total of 0.74'' (19mm) of additional steering rack travel = more lock.

I've installed the rack spacer and I've got a heap of toe in, what happened?

After you have centred your rack (this is CRUCIAL) you may need need to trim your tie rod ends down to counteract the length that you've just put into the length of the rack. Whether you need to trim the tie rods down depends on your setup (Ie. if you've got longer LCA's or aftermarket knuckles you may not need to). Do NOT trim too much off or else you'll need to get a new tie rod and only trim down once you've centred the rack. Note that the LH side has a larger spacer so it will need the most attention.

What's the difference between this screw on steering rack spacer and the lock washers that you sell?

The steering rack spacer gives in total an additional 0.74'' (19mm) of travel where as the lock washers only offer 0.47'' (12mm) of travel (0.23'' (6mm) each)


Our new Compatibility checking feature is still being updated and revised. If you have questions about vehicle fitment, please contact us.

Year Make Model Body Engine
1989 Nissan 240SX Coupe KA24E
1989 Nissan 240SX Hatchback KA24E
1989 Nissan 300ZX 4-Seater (2+2) VG30DETT (Twin Turbo)
1989 Nissan Skyline 2-Door RB20DET
1989 Nissan Skyline 2-Door RB26DETT
1990 Nissan 240SX Coupe KA24E
1990 Nissan 240SX Coupe SR20DET
1990 Nissan 240SX Hatchback KA24E
1990 Nissan 240SX Hatchback SR20DET
1990 Nissan 300ZX 2-Seater VG30DE (Non-Turbo)
1990 Nissan 300ZX 2-Seater VG30DETT (Twin Turbo)
1990 Nissan 300ZX 4-Seater (2+2) VG30DE (Non-Turbo)
1990 Nissan 300ZX 4-Seater (2+2) VG30DETT (Twin Turbo)
1990 Nissan Skyline 2-Door RB20DET
1990 Nissan Skyline 2-Door RB26DETT
1991 Nissan 240SX Coupe KA24DE
1991 Nissan 240SX Hatchback KA24DE
1991 Nissan 240SX Hatchback SR20DET
1991 Nissan 300ZX 2-Seater VG30DE (Non-Turbo)
1991 Nissan 300ZX 2-Seater VG30DETT (Twin Turbo)

You recently viewed

Clear recently viewed
Click to edit the product in Ali Orders.
Note: only show for shop owner